IMET H 650

General

THE RIGID VERTICAL DESCENT

The H 650 is defined by its vertical saw frame movement, which is guided by two massive, induction-hardened columns.

• Balanced Vertical Feed: By utilizing a double-column design rather than a pivot, the machine ensures a perfectly parallel feed rate across the entire width of the material, which is critical for maintaining perpendicularity on large H-beams and wide plates.

• Vibration Dampening: The rigid, electrowelded structure and balanced descent significantly reduce vibration during the cutting process, leading to superior surface finishes and significantly extended tool life.

• Wide Working Area: To provide full support for large sections and big diameters, the machine includes a broad working surface. It is equipped with two free rollers before the blade to facilitate material loading and a perforated plate after the cutting line for exit support.

Features

• 6° Inclined Sawblade: The blade is canted at a 6° angle, ensuring it is never parallel to the working plate. This geometry optimizes the cutting cycle by allowing the blade to work only on a material section at any given time, increasing performance and extending blade life.
• Full-Stroke Hydraulic Vise: The horizontal vise features a hydraulic cylinder with a 25.59 in (650 mm) single full stroke for accurate material blocking. It is equipped as standard with a pressure regulator on the hydraulic power unit.
• Mechanical Material Detection: A detection device descends with the bow to facilitate a rapid approach to the material. Upon touching the workpiece, it automatically switches the machine to the operator-set feed rate to optimize cutting time.
• Mobile Panel Console: Features control LEDs for blade tensioning, guard status, motor thermal block, and electrical tension. Operators can choose between three end-cutting modes, including options for the bow to remain down or return with the blade off.
• High Blade Tension: The blade is maintained at a tension of 27,025 PSI (1900 kg/cm2). A safety microswitch provides an immediate stop if the blade loses tension or breaks.
• Motorized Cleaning Brush: Standard motorized nylon brush removes chips from the blade, while a dedicated tray at the back of the machine collects remains transported by the coolant.

Technical Data

• Max Round Cutting Capacity (0°): 20.08 in (510 mm)
• Max Square Cutting Capacity (0°): 18.90 in (480 mm)
• Max Rectangular Cutting Capacity (0°): 25.59 in×17.72 in (650×450 mm)
• Solid Material Capacity (C45): 11.02 in (280 mm) / Up to 13.78 in (350 mm) with optional pack
• Max Bundle Cutting Capacity: 25.59 in×17.72 in (650×450 mm)
• Min Bundle Cutting Capacity: 4.92 in×0.59 in (125×15 mm)
• Blade Dimensions: 209.45 in×1.34 in×0.043 in (5320×34×1.1 mm)
• Blade Speed (VFD): 49−328 ft/min (15−100 m/min)
• Blade Motor Power: 4.02 HP (3 kW) / Optional 5.36 HP (4 kW)
• Machine Dimensions (B×L×H): 74.61 in×112.99 in×90.55 in (1895×2870×2300 mm)
• Weight: 4,630 lbs (2100 kg)

Standard Equipment

• Bimetal bandsaw blade.
• Motorized nylon blade cleaning brush.
• Chips collection tray.
• Hydraulic horizontal vise with full stroke and pressure regulator.
• Two free rollers on the loading side.
• Mobile control console with system LEDs and end-cut mode selectors.
• Blade tensioning control microswitch for automatic stop.

Optionals

• High Performance Pack: Increases solid capacity to 13.78 in (350 mm) using a 5.36 HP (4 kW) motor, 1.61 in(41 mm) blade height, and hydraulic tensioning system.
• Hydraulic Bundle Cutting Device: Horizontal adjusting mechanical device for cutting packs (Max 25.59 in×17.72 in).
• Supplementary Loading Roller: Lifting roller with manual rotation and lever-action lifting to reduce loading friction.
• Laser Ray: Sawframe-mounted projector that points the cutting line onto the material.
• Minimal Lubrication System: Air-oil micro-mist system with a 0.34 gal (1.3 L) tank.